|
Programming Interface Information:
This information is NOT intended to be used as Programming Interfaces of z/VM. |
LCPDU
Control Block Contents
LCPDU DSECT
Cross Reference (Contains links to field and bit definitions)
LCPDU Prolog
NAME : HCPLCPDU
DESCRIPTION: LinkAG LACP Protocol-Data-Unit (PDU) c/b
DSECT : LCPDU
FUNCTION : This control block maps the IEEE 802.3ad-2000
version 1 LACP PDU structure.
The Link Aggregation Control Protocol (LACP)
provides a standardized means for exchanging
information between Partner Systems on a link
to allow their Link Aggregation Control
instances to reach agreement on the identity
of the Link Aggregation Group to which the
link belongs, move the link to that Link
Aggregation Group, and enable its transmission
and reception functions in an orderly manner.
Destination Address (DA):
The DA in all LACP PDUs is the
Slow_Protocols_Multicast address (01-80-C2-00-00-02).
Source Address (SA):
The SA in LACP PDU is the individual MAC address
associated with the port from which the PDU is
transmitted.
Length/Type:
LACP PDUs are always type encoded, and carry the Slow
Protocol type field. The encoding of this type field
is 0x8809.
Subtype:
The Subtype field identifies the specific Slow
Protocol being encapsulated. LACP PDUs carry the
carry the subtype value 0x01.
Version number:
This identifies the LACP protocol version;
implementations conformant to IEEE 802.3ad of the
standard carry the value 0x01.
TLV_type = Actor Information:
This field indicates the nature of the information
carried in this TLVtuple. Actor information is
identified by the value 0x01.
Actor_Information_Length:
This field indicates the length (in bytes) of this
TLV-tuple, Actor information uses a length value of 20
(0x14).
Actor_System_Priority:
The priority assigned to this System (by management or
administration policy), encoded as an unsigned
integer.
Actor_System:
The Actor's System ID, encoded as a MAC address.
Actor_Key:
The operational Key value assigned to the port by the
Actor, encoded as an unsigned integer.
Actor_Port_Priority:
The priority assigned to this port by the Actor (the
System sending the PDU; assigned by management or
administration policy), encoded as an unsigned
integer.
Actor_Port:
The port number assigned to the port by the Actor (the
System sending the PDU), encoded as an unsigned
integer.
Actor_State:
The Actor's state variables for the port, encoded as
individual bits within a single byte, as follows:
1) LACP_Activity is encoded in bit 0. This flag
indicates the Activity control value with regard to
this link. Active LACP is encoded as a 1; Passive
LACP is encoded as a 0
2) LACP_Timeout is encoded in bit 1. This flag
indicates the Timeout control value with regard to
this link. Short Timeout is encoded as a 1; Long
Timeout is encoded as a
3) Aggregation is encoded in bit 2. If TRUE
(encoded as a 1), this flag indicates that the
System considers this link to be Aggregatable;
i.e., a potential candidate for aggregation. If
FALSE (encoded as a 0), the link is considered to
be Individual; i.e., this link can be operated only
as an individual link.
4) Synchronization is encoded in bit 3. If TRUE
(encoded as a 1), the System considers this link to
be IN_SYNC; i.e., it has been allocated to the
correct Link Aggregation Group, the group has been
associated with a compatible Aggregator, and the
identity of the Link Aggregation Group is
consistent with the System ID and operational Key
information transmitted. If FALSE (encoded as a
0), then this link is currently OUT_OF_SYNC; i.e.,
it is not in the right Aggregation.
5) Collecting is encoded in bit 4. TRUE (encoded as
a 1) means collection of incoming frames on this
link is definitely enabled; i.e., collection is
currently enabled and is not expected to be
disabled in the absence of administrative changes
or changes in received protocol information. Its
value is otherwise FALSE (encoded as a 0);
6) Distributing is encoded in bit 5. FALSE (encoded
as a 0) means distribution of outgoing frames on
this link is definitely disabled; i.e.,
distribution is currently disabled and is not
expected to be enabled in the absence of
administrative changes or changes in received
protocol information. Its value is otherwise TRUE
(encoded as a 1);
7) Defaulted is encoded in bit 6. If TRUE (encoded
as a 1), this flag indicates that the Actor's
Receive machine is using Defaulted operational
Partner information, administratively configured
for the Partner. If FALSE (encoded as a 0), the
operational Partner information in use has been
received in a LACPDU;
8) Expired is encoded in bit 7. If TRUE (encoded as
a 1), this flag indicates that the Actor's Receive
machine is in the EXPIRED state; if FALSE (encoded
as a 0), this flag indicates that the Actor's
Receive machine is not in the EXPIRED state.
NOTE-The received values of Defaulted and Expired
state are not used by LACP; however, knowing their
values can be useful when diagnosing protocol
problems.
Reserved:
These 3 bytes are reserved for use in future
extensions to the protocol. They shall be ignored on
receipt and shall be transmitted as zeroes to claim
compliance with Version 1 of this protocol.
TLV_type = Partner Information:
This field indicates the nature of the information
carried in this TLV-tuple. Partner information is
identified by the integer value 0x02.
Partner_Information_Length:
This field indicates the length (in bytes) of this
TLV-tuple, Partner information uses a length value of
20 (0x14).
Partner_System_Priority:
The priority assigned to the Partner System (by
management or administration policy), encoded as an
unsigned integer.
Partner_System:
The Partner's System ID, encoded as a MAC address.
Partner_Key:
The operational Key value assigned to the port
associated with this link by the Partner, encoded as
an unsigned integer.
Partner_Port_Priority:
The priority assigned to this port by the Partner (by
management or administration policy), encoded as an
unsigned integer.
Partner_Port:
The port number associated with this link assigned to
the port by the Partner, encoded as an unsigned
integer.
Partner_State:
The Actor's view of the Partner's state variables,
depicted in Figure 43-8 and encoded as individual bits
within a single byte, as defined for Actor_State.
Reserved:
These 3 bytes are reserved for use in future
extensions to the protocol. They shall be ignored on
receipt and shall be transmitted as zeroes to claim
compliance with Version 1 of this protocol.
TLV_type = Collector Information:
This field indicates the nature of the information
carried in this TLV-tuple. Collector information is
identified by the integer value 0x03
Collector_Information_Length:
This field indicates the length (in bytes) of this
TLV-tuple. Collector information uses a length value
of 16 (0x10).
CollectorMaxDelay:
This field contains the value of Collector Maximum
Delay of the station transmitting the LACPDU, encoded
as an unsigned integer number of tens of microseconds.
The range of values for this parameter is 0 to 65 535
tens of microseconds (0.65535 seconds).
Reserved:
These 12 bytes are reserved for use in future
extensions to the protocol. They shall be ignored on
receipt and shall be transmitted as zeroes to claim
compliance with Version 1 of this protocol.
TLV_type = Terminator:
This field indicates the nature of the information
carried in this TLV-tuple. Terminator (end of
message) information is identified by the integer
value 0x00.
Terminator_Length:
This field indicates the length (in bytes) of this
TLV-tuple. Terminator information uses a length value
of 0 (0x00).
Reserved.:
These 50 bytes are reserved for use in future
extensions to the protocol. They are ignored on
receipt and are transmitted as zeroes to claim
compliance with Version 1 of this protocol.
FCS:
This field is the Frame Check Sequence, typically
generated by the underlying MAC.
CREATED BY :
DELETED BY :
ANCHORED -
LCPDU Control Block Content
LCPDU DSECT
Hex Dec Type/Val Lng Label (dup) Comments
---- ---- --------- ---- -------------- --------
0000 0 Structure LCPDU LinkAG LACP Protocol-Data-Unit
(PDU) c/b
Destination Address
0000 0 Bitstring 6 LCPDEST Destination Address
0LCPDEST LCPSPLAH X'0180C200' LCPSPLAH
Slow-Protocol-Multicast MSB
.... ..1. LCPSPLAL X'0002' LCPSPLAL LSB Bytes
0006 6 Bitstring 6 LCPSOURC Source Address
000C 12 Bitstring 4 LCPVID (0) LACP PDU Verification Fields
000C 12 Bitstring 2 LCPLEN Length/Type Field
00LCPLEN LCPSPTF X'8809' LCPSPTF
Slow-Protocol-Type Field
000E 14 Bitstring 1 LCPSTYPE Slow Protocol Type
.... ...1 LCPLACP X'01' LCPLACP LinkAG Control
Protocol(LACP)
000F 15 Bitstring 1 LCPVER LACP Protocol Version
.... ...1 LCPVER1 X'01' LCPVER1 IEEE 802.3ab
Version 1
***** Actor Information
0010 16 Bitstring 1 LCPTLV TLV_type Actor Information
.... ...1 LCPACTOR X'01' LCPACTOR Actor Information
0011 17 Bitstring 1 LCPAILEN Actor Information Length
...1 .1.. LCPAISIZ X'14' LCPAISIZ Actor Information
Length
0012 18 Bitstring 15 LCPAINFO (0) Entire LACP Actor Information
0012 18 Signed 2 LCPASYSP Actor System Priority
0014 20 Bitstring 6 LCPASYS Actor System ID
001A 26 Signed 2 LCPAKEY Actor Key
001C 28 Signed 2 LCPAPPRI Actor Port Priority
001E 30 Signed 2 LCPAPORT Actor Port
Expired : Indicates the Actor's Receive machine
state.
0 = Expired (not valid)
1 = Valid
Defaulted : Flag indicates that the Actor's Receive
Machine is using defaulted operational
partner information.
Distributing : Datagram Distribution State
0 = Distribution disabled
1 = Distribution enabled
Collecting : Datagram Collecting State
0 = No incomming datagrams accepted
1 = Collecting incomming datagrams
Synchronization : Current link status
0 = Out of SYNC (not in group)
1 = In SYNC (Allocated to the
correct LinkAG group)
Aggregation : Indicates that the system considers
this link to be aggregatable.
0 = Individual Link
1 = Aggregatable
LACP_Timeout : Indicates the time-out control value
with regard to this link.
0 = Long time-out
1 = Short time-out
LACP_Activity : Indicates the Activity control value
with regard to this link.
0 = Passive LACP
1 = Active LACP
0020 32 Bitstring 1 LCPASTAT Actor State
1... .... LCPEXP X'80' LCPEXP Expired
.1.. .... LCPDEF X'40' LCPDEF Defaulted
..1. .... LCPDIST X'20' LCPDIST Distributing
...1 .... LCPCOL X'10' LCPCOL Collecting
.... 1... LCPSYNC X'08' LCPSYNC Synchronization
.... .1.. LCPAGG X'04' LCPAGG Aggregation
.... ..1. LCPTIMEO X'02' LCPTIMEO LACP_Timeout
.... ...1 LCPCCTVY X'01' LCPCCTVY LACP_Activity
...1 11.. LCPENABL LCPCOL+LCPAGG+LCPSYNC LCPENABL
Port enabled in group
0021 33 Bitstring 3 * Reserved for Future Use
***** Partner Information
0024 36 Bitstring 1 LCPPTYP TLV_type Partner Information
.... ..1. LCPTYPE X'02' LCPTYPE Partner Information
0025 37 Bitstring 1 LCPPILEN Partner Information Length
...1 .1.. LCPPISIZ X'14' LCPPISIZ Partner
Information Length
0026 38 Bitstring 15 LCPART (0) Entire LACP Partner Information
0026 38 Bitstring 8 LCPSYSID (0) Partner System INFO
0026 38 Signed 2 LCPSYSP Partner System Priority
0028 40 Bitstring 6 LCPSYS Partner System ID
002E 46 Signed 2 LCPKEY Partner Key
0030 48 Bitstring 4 LCPPRTID (0) Partner Port Information
0030 48 Signed 2 LCPPORTP Partner Port Priority
0032 50 Signed 2 LCPORT Partner Port
0034 52 Bitstring 1 LCPSTATE Partner State
0035 53 Bitstring 3 * Reserved for Future Use
***** Collector Information
0038 56 Bitstring 1 LCPCTVL TLV_type Collector Information
.... ..11 LCPCINFO X'03' LCPCINFO Collector
Information
0039 57 Bitstring 1 LCPCILEN Collector Information Length
...1 .... LCPCISIZ X'10' LCPCISIZ Collector
Information Length
003A 58 Signed 2 LCPDELAY Collector Maximum Delay
003C 60 Signed 4 * (3) Reserved for Future Use
0048 72 Bitstring 1 LCPTTVL TLV_type Terminator
.... .... LCPTINFO X'00' LCPTINFO Terminator Length
0049 73 Bitstring 1 LCPCTLEN Terminator Length
.... .... LCPTLVEN X'00' LCPTLVEN Terminator Size
004A 74 Bitstring 50 * Reserved for Future Use
0000007C LCPMSIZE *-LCPDU Minimum size of a LACP
PDU
007C 124 Signed 4 LCPFCS Frame Check Sequence
0080 128 Bitstring 1 LCP$END (0) The end
Notes : The following assembler equates are defined and can be
used but do not appear in the control block expansion
because they are in the PLX section and PRINT OFF,
NOGEN are in effect.
LCPDU Storage Layout
*** LCPDU - LinkAG LACP Protocol-Data-Unit (PDU) c/b
*
* +-----------------------------------------+-------------+
* 0 | LCPDEST | (006)- |
* +---------------------------+-------------+------+------+
* 8 | -LCPSOURC | LCPLEN |:STYPE|LCPVER|
* +------+------+-------------+-------------+------+------+
* 10 |LCPTLV|:AILEN| LCPASYSP | LCPASYS- |
* +------+------+-------------+-------------+-------------+
* 18 | -(014) | LCPAKEY | LCPAPPRI | LCPAPORT |
* +------+------+-------------+------+------+-------------+
* 20 |:ASTAT|////////////////////|:PTYP |:PILEN| LCPSYSP |
* +------+--------------------+------+------+-------------+
* 28 | LCPSYS | LCPKEY |
* +-------------+-------------+------+------+-------------+
* 30 | LCPPORTP | LCPORT |:STATE|////////////////////|
* +------+------+-------------+------+--------------------+
* 38 |:CTVL |:CILEN| LCPDELAY |///////////////////////////|
* +------+------+-------------+///////////////////////////|
* |///////////////////////////////////////////////////////|
* +------+------+-----------------------------------------+
* 48 |:TTVL |:CTLEN|/////////////////////////////////////////|
* +------+------+/////////////////////////////////////////|
* 50 |///////////////////////////////////////////////////////|
* =///////////////////////////////////////////////////////=
* |///////////////////////////+---------------------------+
* 78 |///////////////////////////| LCPFCS |
* +---------------------------+---------------------------+
*
*** LCPDU - LinkAG LACP Protocol-Data-Unit (PDU) c/b
LCPDU Cross Reference
Symbol Dspl Value -------------- ---- ----- LCP$END 0080 LCPACTOR 0010 01 LCPAGG 0020 04 LCPAILEN 0011 LCPAINFO 0012 LCPAISIZ 0011 14 LCPAKEY 001A LCPAPORT 001E LCPAPPRI 001C LCPART 0026 LCPASTAT 0020 LCPASYS 0014 LCPASYSP 0012 LCPCCTVY 0020 01 LCPCILEN 0039 LCPCINFO 0038 03 LCPCISIZ 0039 10 LCPCOL 0020 10 LCPCTLEN 0049 LCPCTVL 0038 LCPDEF 0020 40 LCPDELAY 003A LCPDEST 0000 LCPDIST 0020 20 LCPENABL 0020 1C LCPEXP 0020 80 LCPFCS 007C LCPKEY 002E LCPLACP 000E 01 LCPLEN 000C LCPMSIZE 004A 0000007C LCPORT 0032 LCPPILEN 0025 LCPPISIZ 0025 14 LCPPORTP 0030 LCPPRTID 0030 LCPPTYP 0024 LCPSOURC 0006 LCPSPLAH 0000 0LCPDEST LCPSPLAL 0000 02 LCPSPTF 000C 00LCPLEN LCPSTATE 0034 LCPSTYPE 000E LCPSYNC 0020 08 LCPSYS 0028 LCPSYSID 0026 LCPSYSP 0026 LCPTIMEO 0020 02 LCPTINFO 0048 00 LCPTLV 0010 LCPTLVEN 0049 00 LCPTTVL 0048 LCPTYPE 0024 02 LCPVER 000F LCPVER1 000F 01 LCPVID 000C
Copyright IBM Corporation, 1990, 2007